![]() This is especially likely if your water is hard, meaning it has a high mineral content, or if it’s been more than 3-6 months since your last descaling. If the ‘Descale’ light remains on after a cycle, it may be necessary to run another descaling cycle. If you own a K-Duo model, look for bundles specifically designed for it. Some even come in bundles with rinse pods and filters for a comprehensive cleaning. These solutions are typically odorless and contain gentle citric acid that effectively removes mineral buildup without damaging your machine. However, there are also third-party descaling solutions available online. ![]() Keurig offers its own descaling solution compatible with all models. For K Duo Keurig models, you’ll need to press and hold the 8 oz and 10 oz buttons for a few seconds to reset the descale alert. Descaling is the process of removing this mineral buildup, and once completed, the ‘Descale’ light should automatically turn off. This buildup can clog your machine and affect its performance. The water you use in your Keurig contains minerals that over time can lead to limescale buildup. This isn’t a signal for costly repairs but a reminder that it’s time for a cleaning routine. When the ‘Descale’ light on your Keurig starts flashing, it’s essentially your coffee maker’s way of asking for a little TLC. If the ‘Add Water’ light is still on after trying these steps, it’s time to ring up Keurig support. Yes, it sounds a bit odd, but shaking the machine can actually dislodge any air bubbles in the waterline. Put everything back together and try brewing again.Keep shaking until you see water flowing out. Hold your Keurig with both hands and shake it like you’re mixing a cocktail.Unplug your Keurig and remove any coffee pods, the water reservoir, and the drip tray.Here’s a somewhat unconventional but effective way to fix it: This usually happens when the machine runs with too little water. Sometimes, the issue isn’t a blockage but an airlock in the waterline. If not, your Keurig waterline might have Airlocked. The Add Water light should now be off, and you’re good to go. If the “Add Water” light turns off, you’ve solved the problem! Wash the tank with soapy water, fill it up to the MAX line with fresh water, and put it back on the brewer.If you find anything stuck there, clear it out. Next, examine the nozzle where the tank connects to the brewer. ![]() If you see any blockages, clean them using a cotton swab dipped in vinegar. Flip the tank over and look at the valve at the bottom.Take off the water reservoir and empty it.It would help if you cleaned the valve before fixing anything else. ![]() The Keurig may indicate a low water level in the reservoir due to possible blockage in the valves that connect the reservoir to the brewer. Let’s break down how to tackle each issue. What gives? Well, there are usually two main culprits: a blocked valve or an airlock in the waterline. So, you’ve filled the water tank to the brim, but that pesky “Add Water” light just won’t quit. If the water amount is still off, move on to the last step. Change it every 2-3 months for the best results. If the water amount is correct, you need a new charcoal filter. Run another water-only brew and measure it. If you have a water filter in the tank, take it out. If the water volume matches your chosen size, congrats, you’ve fixed your Keurig! If not, let’s move to the next step. Run a water-only cycle at either 6 oz or 8 oz into an empty cup. Fill the tank with fresh water and place it back, making sure it connects securely. Also, make sure the filter in the tank sits right in its holder. Check for any blockages at the bottom valve of the tank and the base unit. Here’s how to tackle this issue: Step 1: Check the Water Reservoirįirst things first, remove the water tank and empty it. These lights are usually blue, but your Keurig might have different colors. When all the lights on your Keurig are on and won’t turn off-usually the ‘Add Water,’ ‘Heating,’ and ‘Medium Cup’ lights-it’s often a sign that something’s up with the charcoal filter or the needle in your machine. If your Keurig light is blinking, figuring out which pattern is displayed before starting any fixes is essential. There are a few flashing light error codes, each with a specific meaning. The blinking pattern on your Keurig can tell you what kind of troubleshooting you might need to do.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |